Insulation Removal and Replacement Bryan TX means pulling out saturated or contaminated insulation and installing new material that actually performs. If a pipe burst, roof leak, or slab leak soaked your attic or walls, that insulation is holding moisture against your framing. We serve homeowners and property managers across Bryan, Texas, with same-day extraction, structural drying, and code-correct replacement. Call (979) 325-7976 and we'll assess it today.
Insulation Removal and Replacement Bryan TX is a two-part restoration service that removes water-damaged, mold-contaminated, or pest-infested insulation and installs new insulation to restore your home's thermal envelope. We start by isolating the work area with plastic sheeting and negative air machine filtration, then pull the old material into sealed bags. Every cavity gets checked with a moisture meter and boroscope camera before we call it dry. Only then do we install new batts or blown-in insulation rated for your climate zone.
Bryan homeowners call us most often after a pipe burst, roof leak, or appliance leak soaks attic insulation. Once fiberglass or cellulose gets wet, it loses R-value fast and becomes a sponge against your drywall and framing. We also handle emergency insulation removal after water damage Bryan TX when storm water pushes through soffits or a slab leak wicks up into wall cavities. Left alone, that moisture feeds mold growth within 24 to 48 hours.
Every job includes the core scope below. Add-ons like mold remediation, drywall repair, or full pack-out are quoted separately after inspection so you're not paying for work you don't need.
We check every accessible cavity with a moisture meter, thermal imaging camera, and boroscope. You get a written report with photos showing exactly where the wet zones are and how far the moisture traveled.
Doorways, HVAC returns, and stairwells get sealed with plastic sheeting. A negative air machine keeps dust and spores out of your living space during the entire tear-out.
All damaged insulation is bagged, removed, and disposed of per Texas regulations. We haul it off-site so you don't have a pile of wet fiberglass sitting in your driveway.
Every exposed cavity gets sprayed with antimicrobial solution and disinfectant. This is standard practice on any job where water sat more than 24 hours, and it's included in our price.
We install new batts or blown-in insulation to the R-value your home needs for this climate zone. Air gaps around can lights, top plates, and penetrations get sealed before we close up.
We walk the attic, walls, and crawl space with a moisture meter, thermal imaging camera, and boroscope camera to find every wet zone. You get a written scope the same day, plus photos of what we found. This is where we confirm whether the insulation can be dried or has to come out.
We seal doorways and HVAC returns with plastic sheeting and set up a negative air machine so dust and spores don't migrate into living space. Old insulation goes into sealed bags and out to the curb. A typical 1,200 square foot attic takes four to six hours to strip.
With the insulation gone, we set Dri-Eaz and Phoenix Restoration Equipment dehumidifiers and air movers to dry the framing and sheathing. Cavities get treated with antimicrobial solution. We monitor with a hygrometer and infrared thermometer until readings hit dry standard, usually 24 to 72 hours.
Before anything new goes in, we re-check every cavity. If mold growth was present, we follow IICRC AMRT protocols and can arrange third-party clearance testing. You get documentation of dry readings, which your insurance adjuster and any future buyer will want to see.
We install new batts or blown-in insulation to the R-value your home needs, seal air gaps around can lights and top plates, and reinstall any drywall or baseboards we removed. Final walkthrough takes about 30 minutes, and we leave the workspace cleaner than we found it.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Pin and pinless meters check moisture content in insulation, drywall, and framing. We use them to map wet zones and confirm dry standard before reinstalling insulation.
Infrared cameras reveal temperature differences that indicate hidden moisture behind walls and under insulation. Essential for finding wet spots you can't see.
A flexible inspection camera lets us look inside wall cavities and crawl spaces without cutting open drywall. We use it to verify dryness and check for mold growth.
Refrigerant and desiccant dehumidifiers pull moisture out of the air and structure. We size them to the cubic footage of the affected space and monitor daily.
Creates negative pressure in the work zone so dust and mold spores don't migrate into living space during tear-out. Standard on every insulation removal job.
Hygrometers measure relative humidity; infrared thermometers read surface temps. Together they tell us when the cavity is truly dry, not just dry to the touch.
Used after removal to neutralize musty odors left behind by wet insulation. We run it in unoccupied spaces and ventilate before anyone returns.
A supply line in the attic froze and split during a cold snap. About 500 square feet of blown-in insulation was saturated, and water had dripped through the ceiling into a bedroom below. The homeowner called us at 6 a.m.
We extracted standing water, removed all wet insulation, and ran dehumidifiers and air movers for 48 hours. New blown-in insulation was installed on day four. Moisture readings confirmed dry standard, and the ceiling was repaired and painted.
A slab leak under a 1960s home in Bryan Heights had been wicking moisture into crawl space insulation for months. The homeowner noticed a musty smell and high electric bills but didn't know why.
We removed all wet batts, dried the floor joists, treated the cavity with antimicrobial solution, and installed closed-cell insulation. A vapor barrier went down on the crawl space floor. Electric bill dropped about $35 the next month.
A sewer line backup sent contaminated water into a ground-floor bathroom and soaked the wall insulation behind the tub. The homeowner called us the same day, and we confirmed the insulation was a biohazard.
We removed the contaminated insulation under OSHA protocols, disinfected the cavity, dried the framing, and installed new insulation. Third-party clearance testing confirmed the space was safe. Total job took five days.
Most Bryan homeowners don't realize their insulation is the problem until something else fails. Here's what we see most often.
Ask a pro →We trace the leak, remove all saturated insulation, dry the decking and joists with air movers and dehumidifiers, then install new insulation once moisture readings hit dry standard. Most jobs run three to four days.
We pull the wet batts, dry the joists, treat with antimicrobial solution, and install closed-cell insulation that resists moisture uptake. We also check for hidden water damage with a boroscope before closing up.
We follow IICRC AMRT protocols: contain the area, remove contaminated insulation, HEPA-vacuum the cavity, apply antimicrobial solution, and arrange third-party clearance testing before installing new material.
We remove all contaminated insulation, disinfect the cavity, seal entry points, and install new insulation. We also document the pest damage for your insurance claim if it qualifies.
“A pipe burst in the attic on a Sunday night. Bryan Restoration Pros had a crew out by 11 p.m. pulling soaked insulation and setting up dryers. They came back every day to check readings and had new insulation in by Thursday. Insurance covered it and the paperwork was ready before the adjuster even called.”
Marcus T.Homeowner, Bryan Heights
✓ Verified“We manage six rentals in Copperfield and one had a roof leak that soaked the attic insulation for weeks before anyone noticed. The crew removed everything, treated for mold, and replaced the insulation. They documented every step with photos, which made the owner's insurance claim painless. We use them on all our properties now.”
Sandra R.Property Manager, Copperfield
✓ Verified“I called three companies about crawl space insulation that was wet from a slab leak. Two wanted to just dry it. Bryan Restoration Pros tested it, showed me the moisture readings, and explained why it had to come out. New closed-cell insulation went in two days later. My electric bill dropped about $40 the next month.”
David K.Homeowner, The Traditions
✓ VerifiedMost Bryan attic jobs run $1,800 to $4,500 in 2026, depending on square footage, insulation type, and how much drying is needed. Wall cavity work costs more per square foot because of access. If mold remediation is required, add $800 to $2,500. We give you a written range after the inspection, and we bill insurance directly when the loss is covered.
Fiberglass batts that got splashed can sometimes be dried in place if we catch them within 24 hours. Blown-in cellulose and any insulation that's been saturated for more than a day almost always needs replacement. Once cellulose compacts, it never returns to its original R-value, and wet fiberglass holds moisture against framing. We test with a moisture meter and tell you straight.
A typical 1,200 to 1,500 square foot attic takes two to four days total. Tear-out is one day, drying runs 24 to 72 hours, and new insulation install is half a day. Wall cavity jobs add a day or two. If mold remediation is involved, plan on five to seven days from start to clearance.
For most Bryan homes we install blown-in fiberglass or mineral wool in attics, and closed-cell spray foam in crawl spaces and rim joists where humidity stays high. Closed-cell foam resists moisture uptake, which matters in our climate. The right choice depends on your existing assembly, venting, and budget, and we'll walk you through it during the estimate.
Water Damage RestorationThe full-scope service that usually precedes insulation replacement. We extract standing water, dry the structure, and rebuild. Insulation removal is often step one of a larger Bryan water damage restoration job.Explore →
Emergency Water RemovalWhen a pipe burst or appliance leak floods a Bryan home, we pull water fast to limit how much insulation gets soaked. The sooner we extract, the more insulation can be saved.Explore →
Flood Damage CleanupFlood water carries contaminants that ruin insulation on contact. We remove affected material, sanitize the cavity, and install new insulation once the structure is verified dry.Explore →
Water Extraction ServicesTruck-mounted and portable extraction pulls standing water out of carpet, padding, and subfloor. That stops moisture from wicking up into wall cavities and soaking insulation.Explore →
Basement Water RemovalBryan basements and below-grade rooms trap humidity. We pump out water, dry the space, and replace any insulation that absorbed moisture against the foundation wall.Explore →
Crawl Space Water RemovalCrawl space insulation is the first thing to fail after a slab leak or heavy rain. We remove wet batts, dry the joists, and reinstall moisture-resistant insulation.Explore →
Sewage Backup CleanupSewage-contaminated insulation has to be removed, no exceptions. We handle the tear-out, disinfection, and replacement following biohazard protocols.Explore →
Storm Damage RestorationHail and wind-driven rain push water through roof decking and soffits, soaking attic insulation. We tarp, extract, remove damaged insulation, and rebuild.Explore →Wet insulation doesn't dry itself out. Call (979) 325-7976 and we'll be at your door with moisture meters and extraction gear, usually within 90 minutes. Free inspection, upfront pricing, and we bill insurance directly on covered losses.
Call Now (979) 325-7976 →If you have water damage, call us at (979) 325-7976. We answer 24/7 and dispatch crews around the clock. If you prefer email, send us a message at info@bryanrestorationpros.com and we will get back to you quickly. We serve all of Bryan and Brazos County, including ZIP codes 77801, 77802, 77803, 77805, 77807, and 77808.